MPPT 75/15 Controller

Victron Energy SCC010015050R BlueSolar MPPT Charge Controller 75/15

On sale ~~$104.00~~ $88.40

Maximum Power Point Tracking (MPPT) is a technique used to get the maximum possible power from a solar panel. It is achieved by putting a variable load on the panel so that it achieves its optimum output voltage, and then converting that voltage to the optimum required by the battery. The effect of this can be to produce output up to 30% higher than a similar panel without this technology. This solar charge controller automatically adjusts for 12 or 24 volt systems.

Questions about this item? Ask here.

p/n: SCC010015050R

Availability: In stock

Quantity

Description
Questions and Answers
Additional information

Maximum Power Point Tracking (MPPT) is a technique used to get the maximum possible power from a solar panel. It is achieved by putting a variable load on the panel so that it achieves its optimum output voltage, and then converting that voltage to the optimum required by the battery. The effect of this can be to produce output up to 30% higher than a similar panel without this technology. This Victron MPPT charge controller automatically adjusts for 12 or 24 volt systems.

Ultra fast Maximum Power Point Tracking (MPPT)
Intelligent battery life program
Auto Detect 12 or 24 Volts
Can be used with any panel output voltage up to 75 Volts
Maximum 15 Amp load, 12 or 24 Volt
Max PV Power in a 12 volt system is 200 Watts
Max PV Power in a 24 volt system is 400 Watts
Built in over temperature protection
Reverse polarity protection
Output shore circuit protection
Internal circuits IP protected
Click for datasheet
Read the Blog Post
Programming requires the use of a VE-USB controller an MPPT control or a Bluetooth Dongle
NEW UL 1741 and CSA C22.2 Certification
Read what the load output is used for in this blog post

Q: Can I parallel this controller with using just one dongle ? What is the correct way to wire them.

Asked by: Lance Mueller - 11/29/2017

A: You can only use one charge controller per dongle.

You can switch the dongle from one charge controller to the other to extract the history for the last 30 days from each since the memory is stored in the charge controller, not the dongle.

Was this answer helpful? 1 of 1 Customer(s) found this Answer helpful.

Answer provided by: Peter Kennedy (11/30/2017)

Submit an answer

Q: Will this controller work with a 180W 36.8V 4.9A SDM-170?x-72 solar panel?

Asked by: Tom - 11/8/2017

A: Yes, it is good for up to 200 Watts of PV power in a 12 volt system and 400 Watts of PV power in a 24 volt system. As long as the open circuit voltage of your panels is less than 75 volts, or preferably less than 70 volts, you are good to go.

Was this answer helpful? 0 of 0 Customer(s) found this Answer helpful.

Answer provided by: Peter Kennedy (11/9/2017)

Submit an answer

Q: I am confused ... does this come with the dongle? To use the blue tooth feature do you not need the dongle?

Asked by: Nate - 2/3/2018

This does not come with Bluetooth or a dongle. To use it for Bluetooth you can add a dongle.
If its a new installation its more economical to buy the "Smart" MPPT 75/15 version which has Bluetooth built-in.

Was this answer helpful? 0 of 0 Customer(s) found this Answer helpful.

Answer provided by: Administrator (6/29/2019)

Submit an answer

Questions about this item? Ask here.

	12 Volt Battery	24 Volt Battery
	Max Panel Watts	Max Panel Watts
MPPT 75/10	145	290
MPPT 75/15	200	400
MPPT 100/20	290	580
MPPT 100/30	440	880
MPPT 150/35	500	1000
MPPT 100/50	700	1400
MPPT 150/85	1200	2400
MPPT 150/100	1450	2900

One of the pictures above shows the programming interface on a PC. In the image the MPPT controller is connected to a PC using the VE USB Interface. In this example I am using one of the earlier 70/15 charge controllers. I turned off autodetect and set the battery nominal voltage to 12 volts so it would show the default settings for a 12 volt system. The absorption voltage default is 14.4V and the Float voltage is 13.8 V

By default autodetect is on so this controller automatically adjusts for 12 or 24 volt battery banks. In a 24 volt systems the absorption and float voltage defaults would be twice what is shown above. With the aid of this program you can set your own values on the computer and write them to the controller when you save and exit. The software is a free download from the Victron website.

Tech Tip

Connecting solar panels in series makes for a higher input voltage to the MPPT controller which gives it more to work with and greater efficiency. It also makes for less voltage drop in the wires. The first number of the model number is the maximum input voltage, the second number is the maximum amperage

NEW

If you add the Victron Energy Bluetooth Dongle you can read the information on your iPhone or Android device. However to program the charge controller you need either the MPPT Control or the VE USB Direct connection to a computer because as of now the Dongle can not be used for programming.

This charge controller takes a 20 Amp Fuse, click on the images below for more details:

BlueSolar charge controller	MPPT 75/15
Battery voltage	12/24 V Auto Select
Rated charge current	15 A
Maximum PV power, 12V 1a,b)	200 W
Maximum PV power, 24V 1a,b)	400 W
Automatic load disconnect	Yes, maximum load 15 A
Maximum PV open circuit voltage	75 V
Peak efficiency	98%
Self consumption	10 mA
Charge voltage 'absorption'	14,4 V / 28,8 V (adjustable)
Charge voltage 'float'	13,8 V / 27,6 V (adjustable)
Charge algorithm	Multi-stage adaptive
Temperature compensation	-16 mV / øC resp. -32 mV / øC
Continuous/peak load current	15A / 50A
Low voltage load disconnect	11,1 V / 22,2 V or 11,8 V / 23,6 V or BatteryLife algorithm
Low voltage load reconnect	13,1 V / 26,2 V or 14 V / 28 V or BatteryLife algorithm
Protection	Battery reverse polarity (fuse) Output short circuit / Over temperature
Operating temperature	-30 to +60øC (full rated output up to 40øC)
Humidity	95 %, non-condensing
Data communication port	VE.Direct See the data communication white paper on our website
Enclosure
Colour	Blue (RAL 5012)
Power terminals	6 mmý / AWG10
Protection category	IP22 (connection area)
Weight	0,5 kg
Dimensions (h x w x d)	100 x 113 x 40 mm
Standards
Safety	EN/IEC 62109
1a) If more PV power is connected, the controller will limit input power to the stated maximum.
1b) PV voltage must exceed Vbat + 5V for the controller to start. Thereafter minimum PV voltage is Vbat + 1V

Manufacturers website

Manufacturers Datasheet

Victron Energy SCC075015060 Smart Solar MPPT 75/15 Charge Controller with Bluetooth

~~$139.00~~ $118.15 Sale

In stock

Add To Cart

Victron Energy BAM010700000 BMV700 Precision Battery Monitor

~~$169.00~~ $143.65 Sale

In stock

Add To Cart

Victron Energy BPP010300100 Color Control GX

~~$608.00~~ $516.80 Sale

In stock

Add To Cart

Victron VE.Direct Bluetooth Smart dongle

~~$58.00~~ $49.30 Sale

In stock

Add To Cart

Victron Energy SCC900500000 MPPT Control

~~$92.00~~ $78.20 Sale

In stock

Add To Cart

Victron Energy SCC950300200 MPPT WireBox Small

~~$23.00~~ $19.55 Sale

In stock

Add To Cart

Victron Energy BAM010700000 BMV700 Precision Battery Monitor

~~$169.00~~ $143.65 Sale

In stock

Add To Cart

Blue Sea Systems Custom Made Circuit Breaker Panel

Price Varies

Put your name on the waiting list for this item

Add To Cart

Victron VE.Direct Bluetooth Smart dongle

~~$58.00~~ $49.30 Sale

In stock

Add To Cart

Victron Energy SCC010015050R BlueSolar MPPT Charge Controller 75/15

Q: Can I parallel this controller with using just one dongle ? What is the correct way to wire them.

Q: Will this controller work with a 180W 36.8V 4.9A SDM-170?x-72 solar panel?

Q: I am confused ... does this come with the dongle? To use the blue tooth feature do you not need the dongle?

NEW

Related Items

Accessories

Recently Viewed Items